Custom baseball uniforms · made on our own floor

Custom Baseball Jersey & Uniform Manufacturer

Jersey and pant drafted together — placket, inseam and knee — in tackle-twill or full sublimation. From 30 sets.

  • From 30 pieces
  • For teams & clubs
  • Names & numbers — no extra minimum

We make custom baseball kits — button-front jersey shirts, pants and caps, matched across the roster, with a different name and number on every piece. Cut, sewn and numbered on our own floor in Sialkot, and kept on file so next season still matches. Bulk runs 3–4 weeks after you approve the sample.

Just share your idea. We review it and propose next steps within 24 hours.

  • Jersey, pant and cap drafted togetherOne kit, not three separate orders — placket, inseam and knee are specified before anything is cut.
  • Two fabrics, one team colourPant poly is heavier than the jersey knit and takes dye differently, so a shared colour is proved on a lab dip first.
  • Tackle-twill stitched through the panelLetters and numbers sewn down rather than heat-pressed — or dyed into the fibre by sublimation where you want the modern look.
  • Full-button or two-button placketClean buttonholes, reinforced at the stress points, on a sample you hold before any bulk is cut.

From 30 pieces per design — but you start with a single-piece sample and approve it before you commit. Names and numbers do not raise the minimum.

Silhouettes

Start with the kit.

Every piece runs in any of the fabrics on the next section — and each one can carry a different name and number.

Button-front Jersey

Full-button or two-button jersey shirts, panelled cut-and-sew or fully sublimated, with piping to your spec.

The spec

Fabric
Sublimation-ready poly
Placket
Full-button or two-button
Names & numbers
Per piece, no extra minimum

Baseball is a two-garment problem: the placket and shoulder on the jersey, the inseam and knee on the pant. Send us a set your team wears now and we draft both to match.

Start your baseball uniform project

Baseball Pants

A reinforced knee, belt loops, and an elastic or open hem.

The spec

Fabric
Durable pant poly
Knee
Reinforced
Hem
Elastic or open

Baseball is a two-garment problem: the placket and shoulder on the jersey, the inseam and knee on the pant. Send us a set your team wears now and we draft both to match.

Start your baseball uniform project

Cap

An embroidered front logo on a structured or soft crown.

The spec

Decoration
Embroidered front logo
Crown
Structured or soft

Baseball is a two-garment problem: the placket and shoulder on the jersey, the inseam and knee on the pant. Send us a set your team wears now and we draft both to match.

Start your baseball uniform project

Warm-up / BP Jersey

A pullover batting-practice top in the team colours.

The spec

Body
Pullover
Colours
Matched to the kit

Baseball is a two-garment problem: the placket and shoulder on the jersey, the inseam and knee on the pant. Send us a set your team wears now and we draft both to match.

Start your baseball uniform project

Fabric

Built to take a slide and a season.

Sublimation-ready poly
Polyester-dominant knit that takes names, numbers and edge-to-edge colour without cracking or peeling.
Performance knit
Moisture-wicking stretch for jerseys worn every innings.
Durable pant poly
A heavier poly for pants that take the slide and the wash.
Interlock
A denser, smoother hand for a more premium jersey.

Different fabrics take dye differently, so a shared colour across jersey and pants may need a lab dip — we'll say so rather than hope. Sample in about 7 days.

Colourways

Your colours, held across the whole kit.

Classic two-colour
White body with red, navy, royal or black trim — the combination most teams start from, and the one that photographs best under floodlights.
Grey road kit
The traditional away set: heather or solid grey body, team colour on placket, piping and lettering.
Full-colour body
Solid or sublimated colour edge to edge, including sleeves and shoulders — only possible on sublimation-ready poly.
Piping & placket contrast
Contrast piping down the placket, sleeve and side seam, in a third colour if you want one.
Matched across garments
The same colour on the jersey, the pant and the cap — which is a lab-dip question, not a wish, and we handle it before cutting.

Send a Pantone reference, a photo, or the jersey you wear now. Colour across separate dye lots and different fabrics is the thing that most often goes wrong on a team kit, so we lab-dip and show you the match before bulk rather than hoping it lands. Your approved colour is then held on file for the reorder.

Built for the roster

Built for the roster, kept for the reorder.

Cut-&-sew or sublimated
Panelled cut-and-sew, or all-over sublimation for edge-to-edge colour and piping.
Button placket
Full-button or two-button plackets, clean buttonholes, reinforced at the stress points.
Per-piece names & numbers
Every jersey a different name and number, at the same price, without raising the minimum.
Full size range
Youth through 5XL in one order, against your minimum — a roster is never one size.
Pattern on file
Your spec and pattern kept on our own floor, so next season's run comes off the same standard.
Individual handout packing
Bagged by name or number, so a kit handout doesn't become a sorting job.

The real test of a team kit is the reorder that has to match. Your pattern and spec stay on our floor.

Decoration

Twill, tackle, and numbers that hold.

Tackle-twill
Stitched-on twill lettering and numbers — the classic baseball look, built to last.
Sublimated names & numbers
Dyed into the fibre — won't peel, and runs edge to edge on poly kit.
Embroidered cap & crest
Front cap logos and chest crests, dense and premium.
Sponsor prints
Screen print or DTF for sleeve and back sponsor marks.

Often more than one method on a single kit — send your logo and roster and we'll map the methods before you commit anything.

Talk to the founder, approve the sample, then we make it.

Send your idea, tech pack or a kit you own — a real person replies within 24 hours. Approve a single-piece sample in about 7 days; bulk runs 3–4 weeks after approval; DDP delivery lands in 4–7 days. Names & numbers included.

Your price is five decisions.

Fabric & weight, construction, decoration, quantity and trims & private label set your price. Every quote is DDP — freight, duty and VAT itemised — and a real spec gets a reply within 24 hours.

Why teams build with us, not through a broker.

You deal directly with the people who cut and sew your order — one floor in Sialkot, no agent between you and it. Before you commit, see the factory on a live video call: your camera, your questions, no script. Payment is staged 40/30/30 (50/50 on runs under 30 pieces) against proof at every stage, with a fix-or-hold remedy if something's off.

Frequently asked questions

Can't find what you're looking for? Reach out to our team.

Tackle-twill is the classic stitched-on look and holds up for years; sublimation dyes names and numbers into the fibre with no added weight. We'll sample either — many teams run twill on the back and sublimation elsewhere.

Start your project

See us before you commit.

Book a live tour, or send your logo and roster and we'll propose next steps within 24 hours. A single-piece sample is how most orders start — approve the real garment before bulk.

Need help with your baseball kit order? info@wearableapparels.comWhatsApp